跳至主要内容

Order of Putting on And Taking Off Personal Protective Equipment

 1. The order of wearing protective equipment

(1) Wearing one-piece protective gown

① Wear disposable hats.

②Wear a mask or a full-face protective mask, and check the tightness of the mask.

③ Put on goggles or mask.

④ Wear one-piece protective clothing (wear a protective clothing hat)

⑤ Wear boots or sterilizable protective foot covers.

⑥ Put on gloves and put them around the cuffs of the protective clothing.


2. Take off the protective clothing

①Leave the isolation room or contaminated area. Take off in the isolation room (cannot pollute other people)

②Take off the gloves, put them inside out and put them in a yellow plastic bag.

③Take off the protective clothing and shoe covers, put the inside out, and put it in a yellow plastic bag.

④ Take off the protective glasses or full face shield. Take off the mask, first take off the lower mask belt, and then take off the upper mask belt together with the mask. Take care not to touch your face with your hands.

④ Take off the protective glasses or full face shield.

⑤Put your fingers back into the hat, gently take off the hat, put it inside out, and put it in a yellow plastic bag.

⑥ Hand disinfection.


Precautions

(1) Medical protective masks should be replaced every 4 hours if they are contaminated.

(2) The glasses worn should be disinfected before leaving the isolation area.

(3) Isolation clothing or protective clothing can be used continuously when medical personnel are in contact with multiple confirmed cases.

(4) In contact with suspected cases, isolation clothing or protective clothing should be changed between contacts with each case.

(5) Isolation clothing or protective clothing should be replaced in time when it is contaminated by the patient's blood, body fluids, or dirt.

(6) Face tightness test should be carried out when wearing medical protective mask or respirator.

(7) When taking off the protective equipment, pay attention not to touch the clothes and skin worn inside. Or wet, it should be replaced in time.

评论

发表评论

此博客中的热门博文

Biodegradability, reusability and safety of protective clothing

  Microplastic pollution, known as "pm2.5 in water", has become a direct source of pollution in the ocean, soil and drinking water, affecting human health. Medical   protective coveralls   is almost made of different polymer materials. The development of a new material can replace the existing material to form a new series of products. As most of the existing   protective suits  are designed to be disposable, they are used heavily during the pandemic. Used medical   protective clothing   should be disposed of centrally to prevent secondary transmission of the virus. Therefore, protective clothing materials must be developed to be repeatable and degradable. Due to the particularity of application scenarios, most medical  protective gown  is disposable. Therefore, environment-friendly materials should be considered in the development of medical  protective gown , and must be considered before material selection and protective clothes desig...
发表评论
阅读全文

Production process of medical protective clothing

  Generally speaking, the production of medical   protective coveralls   needs to go through the steps of raw material preparation, cutting, stitching, tightening, adhesive and pressing, finished products, sterilization and disinfection, warehousing and so on. Among them, sterilization and disinfection takes the longest time. Ethylene oxide is mostly used for sterilization and disinfection of materials, which requires 7-14 days of analysis, seriously affecting the production efficiency of medical   protective gown , and a more efficient sterilization method is urgently needed. Irradiation sterilization can be sterilized without disassembly and assembly, which is efficient and prevents secondary pollution. In 2011, Japan has listed the operation specifications of irradiation sterilization in the sterilization standard for protective clothing, which will reduce the sterilization time to less than 1 d. In order to address the shortage of medical protective clothes durin...
发表评论
阅读全文

Production requirements for disposable surgical gown

Disposable surgical  gown   Strictly control the sterilization process to strictly control the production environment and packaging process Raw materials entering the factory for inspection; strict control of sterilization process The markings are clearly and correctly printed; the markings are marked in accordance with the relevant requirements. SpecificationTips on the instructions Pre-use training   The properties of the bonded or sewn parts should meet the standard requirements. Disposable surgical gown should be supplied sterile and should be sterilized by a confirmed sterilization process. Chemical performance requirements If the disposable surgical gown is sterilized with ethylene oxide, the residual ethylene oxide should be no more than 10 mg/kg. Biological performance requires a single-use surgical gown to be non-irritating and delayed hypersensitivity to the skin. Structural requirements such as the tie should specify the length of the ...
发表评论
阅读全文